f. Fifteen-Day Organizational Maintenance
(3) Recoverability code indicates whether
(1) Items authorized for use as required but
unserviceable items should be returned for recovery
not for initial stockage are identified with an
or salvage. Items not coded are expendable.
asterisk in the allowance column.
Recoverability codes are:
(2) The allowance columns are divided into
Explanation
Code
four subcolumns. Indicated in each subcolumn is
the total quantity of special tools authorized for the
R
Applied to Repair parts. (assemblies and com-
number of equipments supported. No quantitive
ponents) Special Tools and Test Equipment
which are considered economically reparable at
allowances are listed in these columns for repair
direct and general support maintenance levels.
parts.
When the item is no longer economically
g. Thirty-Day DS / GS Maintenance Allowance
repairable. it is normally disposed of at the GS
(1) Items authorized for use as required but
level. When supply considerations dictate, some
not for initial stockage are identified with an
of these repair parts may be listed for automatic
return to supply for depot level repair as set
asterisk in the allowance column.
forth in AR 710-50. When so listed, they will be
(2) The allowance columns are divided into
replaced by supply on an exchange basis.
three subcolumns. The quantitative allowance of
Repair parts, Special Took Test Equipment and
s
special tools for DS / G5 levels of maintenance will
represent initial stockage for a 30-day period for the
DSU and GSC activities and which normally
are furnished by supply on an exchange basis.
number of equipments supported. No quantitative
When items are determined by a GSU to be
allowances are listed in these columns for repair
uneconomically reparable. they will be
parts.
evacuated to l depot for evaluation and analysis
h. One-Year Allowances Per 100 Equipments.
before final disposition.
T
High dollar value recoverable Repair parts,
(1) Items authorized for use as required but
Special Tools and Test Equipment which are
not for initial stockage are identified with an
subject to special handling and are issued on an
asterisk in the allowance column.
exchange basis. Such items will be evacuated to
(2) This column indicates the total quantity of
the depot for overhaul or final disposition.
special tools required for distribution and
Communication-Electronics and Missile
contingency planning purposes. NO total quantities
support items will be repaired/ overhauled
only- at depots.
are listed in this column for repair parts.
U
Repair parts. Special Tools and Teat Equipment
i. Illustration. This column is divided as follows:
specifically selected for salvage by reclamation
(1) Figure number. Indicates the figure
units because of precious metal content, critical
number of the illustration on which the item is
materials, high dollar value or reusable casings
shown.
or castings.
(2) Item number. Indicates the callout number
b. Federal Stock Number. Indicates the Federal
used to reference the item on the illustration.
stock number assigned to the item and will be used
4. Special Information
for requisitioning purposes.
c. Description. Indicates the Federal item name
a. Parts which require manufacture or assembly
and any additional description of the item required.
of a maintenance level higher than that authorized
Assembly components and subassemblies are
for installation will indicate in the source column
indented under major assemblies. The abbreviation
the higher maintenance level.
"w / e" when used as part of the nomenclature.
b. The following publications pertain to the
indicates the Federal stock numher, includes all
heater and its components:
arm amen t, equipment, accessories, and repair parts
Direct
TM 10-4520-201-14 Organizational.
issued with `the item. A part number or other
and General Support
reference number is followed by the applicable five-
Maintenance Manual
digit Federal supply code for manufacturers in
operator, Organization-
TM 5-2805-256-14
parenthesis. Repair parts quantities included in kits
al. Direct and General
and sets are shown in front of the repair part name.
Support Maintenance
Material required for manufacture or fabrication is
Manual
(MIL-STD
identified.
Engine)
d. Unit of Measure (U/M). A two-character
TM 5-2805-256-24P Organizational,
Direct
alphabetic abbreviation indicating the amount or
and General Support
quantity of the item, as used upon which the
Maintenance
Repair
allowances are based. e.g., ft., ea.. pr-., etc.
Parts List (MIL-STD
e. (Quantity Incorporated in Unit. Indicates the
Engine)
quantity of the item used in the assembly group. A
c. The same illustrations are used to illustrate the
"V" appearing in this column in lieu of a quantity
repair parts and special tools listed in both
indicates that a definite q u a n t i ty
cannot be
organizational maintenance section and direct and
indicated (e.g.. shims. spacers. etc).
general support and depot maintenance section.
iv
