UNIT MAINTENANCE H-45 LARGE RADIANT SPACE HEATER (TYPE II, LIQUID FUEL) NSN <a href="http://spacewaterheating.tpub.com/20/01-329-3451.htm">4520-01-329-3451</a> BURNER SHELL ASSEMBLY INSPECT, SERVICE, REPAIR CONT.

UNIT MAINTENANCE H-45 LARGE RADIANT SPACE HEATER (TYPE II, LIQUID FUEL) NSN 4520-01-329-3451 BURNER SHELL ASSEMBLY INSPECT, SERVICE, REPAIR

UNIT MAINTENANCE H-45 LARGE RADIANT SPACE HEATER (TYPE II, LIQUID FUEL) NSN 4520-01-329-3451 BURNER SHELL ASSEMBLY INSPECT, SERVICE, REPAIR CONT. - TM-9-4520-257-12P_163

TM-9-4520-257-12P Compressor Air Rotary Diesel Engine Driven Skid Mounted 125 cfm at 100 psi Manual
Page Navigation
4520-01-329-3451 BURNER SHELL ASSEMBLY INSPECT, SERVICE, REPAIR" class="tooltip">121 122 4520-01-329-3451 BURNER SHELL ASSEMBLY INSPECT, SERVICE, REPAIR CONT. - TM-9-4520-257-12P_163" class="tooltip">123 4520-01-329-3451 FLOW CONTROL BURNER HOSE REPLACE - TM-9-4520-257-12P_165" class="tooltip">124 4520-01-329-3451 FLOW CONTROL BURNER HOSE REPLACE CONT." class="tooltip">125 4520-01-329-3451 FLOW CONTROL BURNER HOSE REPLACE - TM-9-4520-257-12P_168" class="tooltip">126 4520-01-329-3451 CUP AND CABLE ASSEMBLY SERVICE, REPAIR, REPLACE" class="tooltip">127

TM 9-4520-257-12&P 0035 00 0035 00-2 SERVICE Clean fuel, used to clean parts, is potentially dangerous to personnel and property. Avoid repeated and prolonged skin contact. Do not use near open flame or excessive heat. Failure to do so may result in damage to skin and/or fire/explosion. 1. Clean dirty components by immersing them in or rinsing them with clean fuel. 2. Check for unrestricted fuel flow through the pipe nipple (6), reducer bushing (7), and elbow (8). 3. From the bottom of the burner shell assembly (5), push the burner reaming tool (9) through the underside of the burner up tube (10). REPAIR 1. Replace the flow control burner hose (3) if damaged. (Refer to WP 0036 00.) 2. Replace any damaged parts. INSTALL 1. Apply a small amount of pipe thread sealant to the elbow fitting (8) threads, and install the elbow fitting (8). 2. Apply a small amount of pipe thread sealant to the reducer bushing (7), and install the reducer bushing (7). 3. Apply a small amount of pipe thread sealant to the pipe nipple (6), and install the pipe nipple (6). 4. Install the flow control burner hose (3) on the pipe nipple (6). (Refer to WP 0036 00.) 5. Place the burner shell assembly (5) inside the heater body base (4), and position the burner shell assembly (5) with the pipe nipple (6) facing the front heater base door opening (11) so that the flow control burner hose (3) protrudes through the front heater base door opening (11). 6. Connect the flow control-burner hose assembly (3) to the fuel flow control valve (2), and dispose of the petroleum absorbent mat in an authorized location. 7. Install the fuel flow control valve (2) on the heater body base (4). 8. Install the high fire ring. (Refer to WP 0024 00.) 9. Install the superheater assembly. (Refer to WP 0022 00.) WARNING

Privacy Statement
Press Release
Contact